Underfloor heating rod unimat. Unimat cable and water underfloor heating - selection and installation advice. Which warm floors to choose, Unimat or Veria

About the manufacturer of Unimat floors

K-Technologies is the undisputed leader in the production of electric and infrared heating systems. Two lines are especially popular: and UNIMAT.
All developed systems are constantly being improved. The wishes of consumers, certain discovered shortcomings, are taken into account. As a result, the cable floors, heating mats and infrared films created by the company are distinguished by quality, reliability and long service life.

More recently, K-Technologies has launched the innovative Unimat Aqua water floor system. By expanding the range of products, the company attracted new customers and increased the brand's popularity.

Unimat Aqua water floors

Unimat Aqua capillary underfloor heating kits are an innovative heating system that has no analogues in the Russian Federation. The principle of operation of the drip floor is based on the circulation of a heated liquid under low pressure.
The coolant flows through narrow capillary-like tubes. Heating is carried out using an electronic unit capable of changing the power from 100 to 2400 W. The system does not need to be connected to the boiler, it works completely autonomously.

The advantage of Unimat Aqua is:

No electromagnetic field.
Suitable for use in wet rooms.
Technical characteristics - the floor does not overheat, it is not afraid of being "locked" by furniture.
Floor heating time is reduced to a minimum. The drip floor begins to warm up immediately after starting the system. The intensity of heating the heating medium can vary depending on the set program.
Does not require connection to the central heating system.

The permissible underfloor heating temperature, suitable for most floor coverings, is 27-28 ° C.

Pros and cons of Unimat floors

The choice and installation of the Unimat floor has its pros and cons. The positive aspects are:

Small thickness of the underfloor heating cake. The IR rod system is only a few mm thick, the mats are 0.3 cm. The capillary floors are laid in the screed. For effective heating, it is enough to pour concrete with a thickness of 3 cm.
Electricity consumption - if you connect an infrared warm floor, then the savings compared to a conventional heating cable will be 40-60%.
Sufficient heat output - correct laying of mats, insulation and application ensures full compliance with the parameters specified in the installation instructions. Heating systems can be installed as the main heat source.
A wide variety of connection options. The consumer can choose both IR mats with self-regulating heating and cable floors connected to a thermostat.
Acceptable cost.

The disadvantages of Unimat floor, judging by consumer reviews, are as follows:

There is a high probability of purchasing a heating system with defects.
High installation requirements.
Probability of failure of several heating sections after 1-2 years of operation.

Which warm floors to choose, Unimat or Veria

Despite the listed disadvantages, the products of K-Technologies continue to enjoy popularity.
Compared to Veria, Unimat cable and rod heating systems are more reliable. The manufacturer gives a 15-year warranty, compared to 12 years from the European concern.

Capillary heating Unimat has no analogues at all.Purchase of Unimat heating mats is optimal for cold rooms and rooms with high humidity.

Rod IR underfloor heating Unimat Rail is the most energy efficient heating among a wide variety of similar systems. By installing a Unimat Rail heating system at home, you can save up to 60% of electricity. Thanks to its reliability, practicality, simple installation and comfort, it is chosen by thousands of consumers. What is the difference between the Unimat Rail infrared core underfloor heating system and other similar heating systems? We invite you to work out this issue with us.

Film electric warm floors

The infrared heating film used for the installation of a warm electric floor system is a heating element made of special polymers, on the surface of which carbon-conductive strips are evenly placed.

Film electric underfloor heating has many clear advantages over other options, namely:

Film warm electric floors are suitable for any floor covering.
It can be installed in any room.
No additional permissions are required to install it.
The material is very durable and resistant to mechanical damage.
The infrared electric film floor is reliable and durable.
The thin and flexible material makes it easy to install the underfloor heating system: the versatility of the film allows you to cut sections of any shape in accordance with the place of installation and does not affect the thickness of the floor at all.

Features of the

Unimat Rail has its own unique features, which are as follows:

Saving money and energy saving during operation. Unlike cable systems for underfloor heating, it is more economical by 60%.
The system is not afraid of overheating and "locking" by furniture. If furniture is installed on the heated area, then thanks to the self-regulating function, the heating system will exclude overheating. This allows you not to worry about the arrangement of furniture, even after years. In any season of the year, you can reach the desired temperature both in the country and in your apartment.
Usefulness and environmental friendliness for humans. IR heat has an anti-allergenic effect. The Unimat Rail system consists exclusively of quality materials. Radiation is accompanied by ionization of the air, which will have a positive effect on the health of your children. In addition, the Unimat Rail provides uniform heating of the entire living area.
Can be laid in a screed and in a layer of tile adhesive. Thanks to the special design of the mat, the heating can be laid in the base of the screed. This is especially useful in cases where thick screeds have to be poured.
High reliability. The connection of the heating rods of the mats is made in parallel, so that the heating will not fail soon. Even if one rod is damaged, heating will be carried out by the other rod. The manufacturer's warranty is up to 20 years.
Simple and easy installation. If you are a non-professional, you can still install the Unimat Rail heating system. This is due to the simple design of the rod infrared heating floor.

It is recommended to entrust the connection of the Unimat Rail to the electrical network by qualified specialists. Especially if you have no experience with electricity.

When purchasing a Unimat Rail heating system, the following set of parts is included in the package:

VVGng connecting wires.
Carbon mat in a roll.
End kit UKK.
UKC connector kit.
Corrugated tube equipped with a plug and a metal probe.

It is worth highlighting the main technical characteristics of Unimat Rail IR heating:

The maximum power consumption of heating at a rod temperature of 20 ° C is equal to 116 W / running meter.
The maximum power consumption of heating at a rod temperature of 60 ° C is 77 W / running meter.
The basic width of the mat is 0.83 m.
The maximum allowable serial connection length is 25 running meters.
It has a step of 0.10 m between each rod.
Power supply is carried out at 220/50 V / Hz.
In the total spectrum, the proportion of IR rays is 90.60%.
The IR wavelength ranges from 8 to 14 microns.

As for the installation of the Unimat Rail system, it can be installed under ceramic tiles, carpet, linoleum and laminate. In each individual case, it is important to observe the technology of installation work.

Due to the fact that recently there have been a lot of fakes of Unimat Rail underfloor heating, it is worth paying attention to the distinctive features of this heating. This will allow you to purchase original products.

Due to the wrong choice, you will lose a large amount of money, moreover, cause harm to your health. You should not buy a warm floor of unknown origin.

Below is the difference between reality and fake. Be careful, because your life and money are at stake, of course:

If you bought a fake, then when the heating system heats up to a temperature of 60 ° C, you will feel an unpleasant smell of plastic, which is caused by the mat overheating and melting. This means that the heating mat will fail at any time.
The counterfeit will never be marked or marked, for example, the RHE abbreviation.
Fake Unimat Rail uses simple self-tapping screws in the connections of the rods and the power cable, and not brackets made of copper, as in the original products. After a short time, the screws will oxidize and rust. As a consequence, this will cause sparking.
The fake has a mat width of 80 cm, while the original Unimat Rail has 83 cm. This small difference greatly affects the technical characteristics of the entire system. For example, a width of 80 cm increases the starting currents in a self-regulating system. This negatively affects the reliability of the heating system.

So, if you do not want to fall into the trap of deception and into the hands of unscrupulous dealers, then you should simply adhere to a few rules:

Original Unimat Rail products are sold only as a set. It has everything you need for installation. The set also includes a video instruction on a DVD disc, as well as a color paper instruction.
The connection points of the rods are marked with Unimat Rail.
When the rod is heated to 70 ° C, the original products work without failures.
The product passport must indicate a 20-year warranty.

Unimat characteristics

Let's take a quick look at the characteristics of the Unimat infrared rebar floor. Here is a photo from the instruction:

Unimat infrared core heat-insulated floor. Specifications

The peak (maximum) power consumption is 116 W per linear meter if the regulator is turned on to the maximum. Well, or just plug the heating mat directly into an outlet. As you can see, when heated, the power consumption will decrease. I suspect that if you leave the floor on, it will heat up to 70 or 80 degrees, the power consumption will drop to 60-70 W, and it will stop heating up further. That is, unlike a cable floor, this floor independently excludes overheating.
Consumption per linear meter - 24 watts. Here, apparently, we are talking about the optimal average temperature. If the pitch between the rods is 0.1 m, then 10 rods per 1 meter. This means that each rod consumes an average of 2.4 watts. Not to be confused with peak consumption! The peak will be 116/10 = 11.6 watts.
The width of the thermomat (that is, the length of the rods) is fixed at 0.83 m.
The maximum length of mats connected in series is 25 m. Let's count. 1 meter consumes 116 W at its peak, which means that 25 meters - 2900 W, this is a current of more than 13 A. Considering that the minimum cable cross-section for connection is 1.5 mm2, it is clear why the manufacturer was reinsured.
The proportion of IR rays in the spectrum is 90%. Apparently, the rest of the components lie in the electromagnetic spectrum.
The IR wavelength is average, good for the body. I don't understand this. And I have no idea how to measure and check it.

Warm floor Unimat. Completeness

As you can see, you can buy different lengths of the mat at different prices, the difference will also be in the length of the wire for connection and the number of bells and whistles. By the way, here they are:

Unimat connection and insulation kits

More details on how this is applied can be found in the section on installation.

Power consumption table:

Rates

Rod IR underfloor heating Unimat Rail has several modifications. Each of them has distinctive features, which mainly consist in power and heated area. Several models are shown below:

Unimat HR-S-100 - power 0.13-0.12 kW (m 2 / linear meter). Heated area 1 m 2 - the average price is 2600 rubles.
Unimat HR-S-200 - power 0.26-0.23 kW (m 2 / running meter). Heated area 2 m 2 - the average price is 5270 rubles.
Unimat HR-S-300 - power 0.39-0.35 kW (m 2 / running meter). The heated area is 3 m 2 - the average price is 7900 rubles.
Unimat HR-S-400 - power 0.52-0.46 kW (m 2 / running meter). Heated area 4 m 2 - the average price is 10,500 rubles.
Unimat HR-S-500 - power 0.65-0.58 kW (m 2 / running meter). The heated area is 5 m 2 - the average price is 13,200 rubles.
Unimat HR-S-600 - power 0.78-0.7 kW (m 2 / running meter). The heated area is 6 m 2 - the average price is 15800 rubles.
Unimat HR-S-700 - power 0.91-0.81 kW (m 2 / running meter). The heated area is 7 m 2 - the average price is 18,400 rubles.
Unimat HR-S-2500 - power 3.25-2.9 kW (m 2 / running meter). The heated area is 25 m 2 - the average price is 66,000 rubles.

So, we made a brief overview of the Unimat Rail underfloor heating system. Leave your comments at the end of the article if this heating is already used in your home.

Today, underfloor heating has become the most relevant option for space heating. Innovative solutions - thermomats - have a particularly favorable effect on the microclimate of the house: heated floors based on carbon fiber heating rods emitting infrared waves. They are extremely easy to install.

Infrared underfloor heating Unimat from this series is installed on glue or leveler, mainly under tiles or porcelain stoneware. IR radiation does not transfer heat to the air in the room, but directly to the people who are there. At the same time, the humidity is favorable for living quarters.

Design

The system, which has an innovative heating technology, is based on a unique development of a South Korean company. The design includes rods that do not pose a risk to human health, which are connected to each other in parallel with a protective conductor. They are connected to the mains through a thermostat. The rods have a special coating - a special plastic braid, which counteracts the effects of the environment and protects them during operation, therefore, the Unimat rod-type underfloor heating can also be used outdoors.

On a note

This system is unique because it does not impose any restrictions on the arrangement of furniture.

This design can also be used in rooms with high humidity, so thermomats can be found in water parks, saunas, bathrooms, etc.

Currently, the company produces 2 types of carbon underfloor heating - Rail and Boost. They are almost identical, but there are some differences.

Rail

The construction of this type of carbon floor is completely classic - thin rods are installed at a distance of 10 cm from each other and are connected by lateral conductive cables.

The specificity of this type is significant energy saving during heating. Thanks to the above-described protection principle using polymer composites inside the rods, the total energy savings can be up to 60%.

Rail can be installed in both screed and tile adhesive. The optimum height of the protective cover should be 5 cm. The specific power is 16 W / m², and the maximum is 130 W / m².

Specifications:

But if this degree of heating is not enough, experts recommend installing a more powerful type of carbon floor.

Boost

Outwardly, it is practically no different from the Rail series. The only difference is the power and the distance between the carbon elements. The models in this series have an optimum output of 138 W / m² with a maximum of 160 W / m².Color coding is necessary for quick identification of the species, and also serves as one of the factors of protection against counterfeiting.

Underfloor heating infrared Unimat of the Boost series can be installed not only in residential premises, but also in rooms with high humidity - bathroom, kitchen. During operation, the surface temperature will be in the range of 28-30 ° C.

Specifications:

Completion of standard models. It includes heating elements, wires for connecting to a thermostat, a corrugated tube for mounting a temperature sensor and a connection kit. The latter is intended for installation - with its help, electrical cables are connected on swivel nodes.

"Unimat Boost"

The "Unimat Boost" heating system differs from the "Rail" modification. It is also represented by mats with heating rods. The filler consists of carbon, silver and graphite. The rods are reinforced in 10 cm increments.

A distinctive feature is that the system belongs to self-regulating devices. When overheating or when one of the rods breaks, heating does not stop. Energy is distributed over all elements of Unimat underfloor heating. Power 1 linear m is 138 W.

Underfloor heating "Unimat Boost" is laid in a deep screed or under tile adhesive with a layer thickness of up to 5 cm: such a bulky layer does not affect the heating efficiency. Installation can be done in rooms with any temperature and humidity conditions. The rods are reliably protected by an insulating material that protects the heating element from moisture.

Despite the fact that the manufacturer does not establish restrictions on the use of "Unimat Boost", the system is intended for heating residential and non-residential rooms, but it is not recommended to heat the pool or shower cabins with floor drain with mats. Standing water can negatively affect the concrete screed, penetrate inside to the heating system, to the electrical wiring.

Purchase underfloor heating "boost" from dealers, in Moscow, in St. Petersburg. The manufacturer gives a long warranty period for the heating system, up to 10 years. The period of operation is up to 50 years. If individual rods break, they can be easily replaced with new elements.

Benefits and Testimonials

Environmental friendliness and safety

The thermomat is based on infrared radiation, which ensures uniform heat distribution and optimal humidity in the room. Radiation in this frequency range is absolutely harmless. Today, a rod infrared warm floor is effectively used even in incubators, which are necessary for carrying babies born much ahead of time.

Functionality

The system from Unimat is able to independently distribute heat, that is, the thermomat itself recognizes low-temperature zones during operation and increases the heating level. This applies, for example, to the area of the front door or window - here the heating power increases, but under furniture, in the area of the battery or under pile coverings, it decreases.

How does this happen? The heating element in the system is carbon rods containing finely dispersed graphite. As the temperature rises, the carbon expands. With an increase in the distance between graphite particles, their smallest contacts, on the contrary, decrease. As a result, the resistance of the rods increases, which leads to a significant drop in power. Naturally, this saves the consumed electricity. When the temperature drops, the opposite effect is achieved.

On a note

Thus, the rod is very sensitive to temperature fluctuations at any point. Therefore, overheating of the thermomat and its individual sections is excluded.

Profitability

Typically, resistive heating systems provide energy savings of about 25%. In contrast to them, the core, due to its self-regulation ability, saves at least 50-60%.

Reliability

UNIMAT protects the floor from overheating and resists mechanical stress. The latter provides an optimal conductor design. Due to the parallel arrangement of the rods on it, in case of damage to individual elements, the thermomat continues to work.

On a note

The reliability of the Unimat system is also evidenced by the long operational life, which reaches about half a century.

Versatility

The thermomat can be combined with any floor covering. Since the heat is evenly distributed over the surface of the surface, it does not overheat, and its structure does not change.

Lightness of the device

Lay evenly on a heated surface.

Installation of a self-regulating thermomat

Laying is performed on a cleaned and leveled surface. First of all, the sheets are spread on the base and fixed to the surface with glue or tape. The thermomat begins to unfold, laying the side with the connecting sleeves - they are already installed by the manufacturer - in the direction of connection to the thermostat. This is the front page.

In places where it is necessary to unfold the strip, cut one of the connecting wires and turn it 180 ° C. Unimat can only be split in the center of the power cable between the flexible carbon rods. The strips of the thermomat are fixed on a heat-reflecting substrate and between themselves with adhesive tape to immobilize them. The rods should not intersect with each other.

Connecting IR-mat bands to each other

A special tool is used to strip the insulation from the wire at the cut site. After the insulation is removed, a sleeve, a heat-shrinkable insulation tube, is placed on it and clamped with crimping pliers.

The ends of the VVGng cable used to connect are processed in the same way. Then the ends of the connecting and power cables are put into a sleeve and crimped with pliers. Shrinkage of heat-shrinkable insulation is performed using a technical hair dryer.

The insulation is actually double, since the heat-shrinkable tube of the connecting cable practically slides onto the contact connection. Thus, after thermal shrinkage of the joint, you can no longer worry about its reliability. The process is repeated for all other UNIMAT bands.

Installing a temperature sensor

The device (model SF 7x15) is inserted into the corrugated tube using a probe and a plug is installed on it. For the tube itself, a curtain is preliminarily prepared and "sunk" it in a thin screed or tile adhesive. The corrugated tube with the sensor should be located in the direction of the rods, and there should be no heat-reflecting material above it.

If it is not possible to use a corrugated tube, use another model - SF 7x30. The sensor is installed in the middle of the rods on a substrate and secured with tape.

Installing a thermostat

Wall mounted. For its device, an accurate calculation of power is required, taking into account all devices that may be connected to the mains. For systems with a power of 2 kW and more, the thermostat is connected using a separate machine. The installation of the system can be considered complete only after testing it.

Screed device

For screed or tile adhesive for tiles and porcelain stoneware, it is necessary to ensure good adhesion to the concrete base. The required adhesion can be ensured by cutting 7x15 cm strips on the substrate between the rods of the self-regulating infrared heated floor Unimat.As a rule, they are performed in a step of 30 cm in a checkerboard pattern. The total area of the cutouts is usually at least 25–30% of the used thermal reflective backing.

Cutting holes along the entire rod can result in reduced heating efficiency and increased costs.

The smallest is 2 cm. At lower values, it is impossible to ensure uniform heating of the surface.The surface of the screed must be leveled and after drying, lay the topcoat.

Today, the most popular and relevant is the heating of the house with underfloor heating. We will talk about Unimat infrared floor heating, which provides the ability to keep the room warm, regardless of its area.

Unimat underfloor heating is a fairly well-known product - you can probably find it in any store that sells underfloor heating systems.

How to install XL Pipe liquid floor

Stages of installation of electric water heating xl pipe:

Prepare a rough base. They clean out debris, level out irregularities, close up cracks. Plates of extruded polystyrene foam are laid on the base. It plays the role of a heat insulator.
The heat insulator is fixed with "umbrellas". To do this, holes are made in the plate for fasteners, dowels-umbrellas are inserted there.
A reinforcing mesh is placed on top of the thermal insulation plates. Mesh sizes from 100 to 200 mm.
The mesh sections are tied with a metal knitting wire.
The heating cable from the underfloor heating kit is checked for compliance with the resistance.
Then the pipes are laid out according to the scheme specified in the instructions. The tubes are fixed with plastic clamps to the reinforcing mesh.
The supply cable is laid from the thermostat to the junction box.
The wires from the pipe are connected to the power cable. For this, terminals are usually used.
The grounding cables are connected to the reinforcement mesh.
Fix the temperature sensor approximately 50 mm from the tube.
Close the back box. Seal the cracks with a sealant.
Then they perform the concrete screed and wait for it to dry. Then make a topcoat on top.

When installing XL Pipe electric water floors, the pipes must not be twisted or pinched. The work is carried out taking into account all the recommendations of the manufacturer. In winter, for the fastest drying of the concrete screed, it is allowed to start the system in an average temperature regime.

This system is expensive and must be handled with care during installation, avoiding breakage of the tubes. The XL Pipe heating method is suitable for any premises: residential, office and industrial.

Maintenance work on XL Pipe is carried out by specialists. As a rule, it is required to replace the coolant. This is done about once every 10-15 years. The final floor covering is not touched at the same time. This is a great advantage of XL Pipe over other systems.

The main disadvantage of this heating method is the rather high price of the system itself. However, the reliability, durability and efficiency of heating such underfloor heating justify these costs.

System features

The features of the equipment from this manufacturer are as follows:

Unimat underfloor heating has a specific design that relieves the user of the need to think over the location of the heating sections;
using a thermostat, you can reduce the power in those areas where the heat output decreases;
the principle of self-regulation of infrared heating can reduce electricity consumption by half. With strict adherence to operating rules, savings can be up to 60%;
a specially provided parallel connection allows the heating system to work even if its individual parts are damaged;
Unimat floor thermostats are covered by the manufacturer with a 20-year warranty.

What are liquid electric floors

Consumers have already appreciated the advantages of underfloor heating of a new generation, which autonomously provide electric floor heating with a liquid heat carrier. It is not correct to call these floors electric-water, since the coolant is not water, but antifreeze. Therefore, it is correct to say "liquid floors".

Liquid underfloor heating includes a set of polyethylene pipes with a heat carrier poured into them.An electrical cable is embedded along the entire length of the tubes. When the electric heating is turned on, the coolant is warmed up by the cable and begins to give off heat to the environment.

In various models of liquid underfloor heating, antifreeze or distilled water acts as a heat carrier.

Types of products

Today the model range of warm floors includes:

Unimat Aqua - capillary floor;
Unimat Boost / Unimat Rail - energy-efficient core floors;
Unimat Cord - cable floor.

The principle of operation of the Unimat Aqua is based on the circulation of liquid over the entire surface of the mats. It is mounted under porcelain stoneware, tiles and other coatings. Its installation in an apartment does not require connection to hot water supply or heating system.

Heating occurs due to the presence of a special electronic control unit (its power is 100-2400 W).

compactness;
innovativeness;
reliability and safety;
programmable power;
autonomy of work;
not afraid of overheating;
can be installed in rooms with high humidity.

The youngest representative of underfloor heating in tile adhesive or screed is Unimat Cord. It is a conventional heating mat based on a two-core thin resistive screened cable that is glued to a backing.

This line includes two modifications:

Unimat Cord T. For standard triple-insulated rooms with a power of 130 W / m², and for cold rooms - 200 W / m².
Unimat Cord P. Designed for standard rooms with double insulation and 140 W / m².

By purchasing Unimat CORD underfloor heating, the owner chooses the classic version of the cable type in a more convenient and reliable design. The thermomat is provided with high reliability, which is achieved through high-quality insulation.

This floor is easy to use, as the included adhesive mesh allows you to easily fix the mat during installation.

Differences:

three-layer teflon insulation;
adhesive mesh;
mats of minimum thickness;
long operating time.

Rod underfloor heating Unimat Boost, Unimat Rail are made of thin carbon rods, which are arranged in parallel and connected to each other using a copper cable. In terms of efficiency, these floors are one of the best options for heating your home.

As a rule, they are chosen for the bedroom, kitchen, bathroom.

practicality, comfort, reliability;
low power consumption;
environmental friendliness, which is achieved thanks to the infrared heating principle;
ease of installation.

Laying system (video)

Prices and reviews

The constant striving of a person for comfortable conditions makes him equip his home with more modern, perfect devices. These include underfloor heating systems. However, if the choice fell on a specific manufacturer, then first you should evaluate the reviews about the Unimat rod heat field.

When the choice is finally made and all the advantages and disadvantages are taken into account, the potential buyer proceeds to the necessary calculations.

Before you buy Unimat underfloor heating, you need to calculate the area of the room in which it will be installed. Depending on the specific heating area, the manufacturer offers ready-made kits with a meter step.

Accordingly, the buyer will easily select the optimal solution and he will not have to overpay. For large rooms, the manufacturer has provided an option of 25 running meters.

The price of Unimat underfloor heating depends on the configuration. One running meter of fully-equipped underfloor heating will cost around 25,000 rubles. The above option for large premises will cost the buyer at least 60,000 rubles.

The complete set includes:

Video instruction on disk;
Carbon mat for carpets;
Warranty card;
Connecting wires.
Corrugated tube.
Passport products.
Additionally, the user can purchase a thermostat and heat-reflecting material.

Now here are a few reviews.

Nadezhda, 43 years old, Lobnya:

Three years ago, we installed Unimat core underfloor heating. At first, we could not get enough of it. Heats up quickly and well, while the electricity costs were minimal.
However, two years later, they noticed a significant consumption of electricity, which went off scale for all conceivable and inconceivable parameters. Six months later, in two rooms he was completely out of order. The quality is poor. I would also argue about the savings.

Oleg, 38 years old, Krasnodar:

I bought an infrared heat-insulated floor Unimat for the bathroom. Three running meters was enough for me. Everything is included in the package, but in addition I had to purchase a thermostat. We put Unimat on a screed without heat-insulating material.
The floor heats up very quickly, but electricity consumption is off the charts. For one room, a very necessary thing, but if you heat the whole house, you will have to spend well.

Olesya, 36 years old, Moscow:

The balcony was insulated and the choice fell on the Unimat rod infrared floor. Initially, my husband and I reviewed many other options from different manufacturers. Reviews of the Unimat warm field testified to the fact that it is of high quality, economical and reliable.
Based on this, we bought four running meters and a thermostat. It worked well for two years, but then several rods had to be replaced. The rest of the details work like a clock.

The underfloor heating system is an effective replacement for heaters and traditional heating methods. It helps to create comfortable living conditions both in a country cottage and in an apartment of a multi-storey building, especially during the off-season, when centralized networks are not yet connected. Among the variety offered by manufacturers, UNIMAT underfloor heating is of particular interest to buyers. This is due to the declared technical characteristics and the ratio of price and quality of products.

The main difference of the infrared floor is the use of elastic and flexible carbon rods for the heating elements. They are located parallel to each other and are connected to each other in the form of a mat using a power cable. This design provides uniform heating of the entire surface, and the self-regulating device allows you to control the temperature depending on the operating conditions. By purchasing a core underfloor heating from UNIMAT, you can create a comfortable environment without a significant increase in energy costs, since it is very economical. Laying is carried out under the screed, and it is recommended to use it in rooms with high humidity. An overview of the different UNIMAT models will help you to learn more about the features.

Advantages of electric underfloor heating

Electric underfloor heating systems are becoming more and more popular on the market not only due to the reasonable prices for equipment, materials and components, as well as installation work, but also due to other advantages:

Reliability

New warm electric floors will last for more than a dozen years, while you do not need to obtain special permits to install the system, be afraid of leaks and equipment failure: even in the event of a breakdown of a separate element of the electric underfloor heating, the system will function without interruption.

Profitability

In addition to the fact that even for the best electric underfloor heating, prices are available to a wide range of consumers, you will be relieved of the need to buy additional equipment and spend money on its installation, as in the case of water underfloor heating. Further energy costs are comparable to those with standard heating appliances.

Security

Despite the fact that electrically heated floors, which you can buy at a favorable price on the Caleo Unimat website, emit electromagnetic radiation, such a system does not negatively affect living organisms. Their safety is confirmed by certificates of conformity, guaranteed by manufacturers, and also justified by SNiPs for the installation of this equipment.

Convenience

Warm infrared or cable electric floors can be installed at an affordable price both in the entire apartment and in separate rooms: bathroom, nursery, bedroom, regardless of the type of flooring, since there are systems of warm electric floors under tiles, laminate, carpets, etc. further at the best prices.

Ease of installation

Almost everyone can install equipment: you can buy a warm electric cable floor, and install it yourself. Installation instructions for the system are included with materials and related products.

Ease of operation

Warm electric floors do not require special maintenance, and the heating temperature can be easily controlled with a thermostat. Thanks to the installation of such a system, it is possible to warm up a large room in a short time. Warm electric floors are lightweight and mobile, that is, if necessary, they can be easily dismantled and then installed in a new place.

Uniform heating

The heat from the heated floor gradually rises upward, evenly distributing the warm air and creating the most comfortable conditions.

Buying a cable or infrared electric underfloor heating is an excellent solution for heating a city apartment or a private house, both in terms of price and quality.