How to insulate windows using Swedish technology yourself

Insulation of windows using Swedish technology

The problem of keeping heat in the house is now more acute than ever - in the light of the high cost of heat carriers. One of the most effective methods is to insulate windows using the Swedish Euro-Strip technology for the winter, and, once and for all, there will be no need to do it again and again before each new season. Such insulation of wooden and plastic windows has a service life of up to 15-20 years. Our company carries out custom-made repair and insulation of windows using Swedish technology in Moscow and with a visit to the Moscow region.
Order service

Preparation for work

There is an indispensable condition for insulating works according to the Swedish method - the satisfactory condition of the wooden frames. Therefore, before installation, you should carefully examine the structure.

There should be no damage at the bottom of the sash and frame, where the condensate flows. If there are minor gaps, they need to be putty and painted. The glasses must be intact.

The hinges should not wobble, and the sashes should not sag; if defects are found, the fittings should be replaced. The window itself should open and close well, distortions and gaps are not allowed.

If you are convinced that the window is in good condition or have completed the necessary restoration, you can proceed directly to the insulation.

Benefits of the Euro-Strip method

Firstly, this method can be used to insulate old and new, only installed windows.
Secondly, window insulation using Swedish technology can be performed on any materials. Our specialists will perform Swedish insulation of wooden, plastic PVC, aluminum windows of various shapes and types with the same effect. Including, it is possible to carry out insulation of a roof window of any design, as well as the slopes of plastic windows.
Using this technology, you can not only insulate windows in an apartment, but also a balcony, loggia and door windows - entrance, balcony, vents, etc.
To make this heat-retaining procedure, among other things, is very profitable - the price for Swedish insulation of old wooden windows is ten times less than buying and installing new ones.
The effectiveness of this method is very high - it makes it possible to completely eliminate drafts, exclude the ingress of dust, moisture (no leaks, even in a downpour!), Noise from the street. That is, the repair and insulation of old wooden windows using the Euro-Strip technology gives the effect of a double-glazed unit in metal-plastic windows of the highest quality. There is forever no need to seal with tape even in the most severe frosts, and in the summer, windows can be opened and closed as needed - this does not affect the quality of the seal.

Material features

Tubular Euro-Strip is a certified, environmentally friendly material that retains its qualities at temperatures from -80 to +200 degrees. In addition, the manufacturer notes the property to trap radiation radiation. The original material is branded every 75 cm. This composite material is made on the basis of silicone rubber with the addition of propylene, a copolymer of ethylene and diene monomer.

Insulation of windows using the Swedish Euro-Strip technology, in Moscow and the Moscow region!

When insulating windows using the Swedish Euro-Strip technology, a 3-stage installation of seals is used. The leaves are removed from the hinges and prepared for the correct installation of the seals.

Stage 1 A Swedish Euro-Strip silicone seal is installed in the end parts of the sash (This is the main seal eliminating 95% of all drafts and blows!)

Stage 2 In the space between the frames (between the sashes), the Swedish EPDM seal is installed. (This is dust and sound insulation) The sashes and frames are adjusted (restoration of the window geometry). This helps the seals eliminate all drafts and blowing, and makes it more comfortable to open and close the window!

Stage 3 At the final stage of window insulation, glass is sealed (these are dust insulation, noise insulation and moisture insulation).

Windows can be insulated with a Swedish tubular sealant in any weather, our specialists do the job quickly and efficiently. In parallel, our masters can perform repairs, restoration of windows, glass replacement, installation of new fittings.

Window

48 votes

Voice for!

—

Against!

In order to save money on the replacement and purchase of a new window, Swedish insulation technology is becoming more and more popular. There is a statement that after this procedure, old wooden windows are able to function for several more years. Moreover, the cost of all materials is available to almost everyone. We will try to figure out whether this is true further.

Features of Swedish window insulation
Insulation of windows using Swedish technology: features and benefits
Swedish technology for insulating wooden windows: general recommendations
Do-it-yourself window insulation technology, characteristics of the seal
Varieties of windows that can be insulated using Swedish technology
How to quickly insulate windows using Swedish technology

Features of Swedish window insulation

Swedish window insulation technology got its name from the materials used in the process of its implementation. Rubber seals are made in Sweden and are of high quality and durability. At the request of manufacturers, this material is capable of performing its functions for more than ten years.

The process of performing insulation according to Swedish technology is rather complicated, for high-quality work, you will need to have skills in working with a certain tool. Since, for example, in order for the seal to be well fixed on the surface of the window, it will be necessary to build a groove section, and for this it is necessary to work with a cutter.

If you turn to the services of professionals, you will have to shell out a lot of money to carry out this process. Insulating a standard window will cost about $ 20. In this case, the list of work includes:

removal of flaps;
preparation of grooves for installing the seal;
installation of a seal;
fitting sashes;
sealing glass areas.

If you need to replace old hardware or repair a window frame, you need to spend extra money.

Tip: To save money when hiring a professional, when insulating a window with two frames, it is recommended to insulate only one of them - the inner one.

But, it is extremely unprofitable to hire specialists to repair and insulate a window using Swedish technology, since the amount of repair will be equal to the cost of an ordinary plastic glass unit. At the same time, you do not need to spend time and effort on restoration. If you want to save money, all the work must be done manually, and if you study all the recommendations well, then it is quite possible to do this.

The owner of the windows faces a difficult choice between buying a new window or insulating an old one. The first option will provide an opportunity to choose a new window, more modern and improved, and in the second option it will receive an old but well-repaired window. The choice is of course for the owner.

If all the details of the window are intact and not damaged by rot or fungus, then it is preferable to choose the Swedish insulation technology, which differs only in positive reviews. If there is damage to the wood on the window, then it is better to give preference to buying a new glass unit.

Insulation of windows using Swedish technology: features and benefits

This technology was developed by the Swedes in order to save energy for heating the premises during the winter season. After its development, it really paid off, and became quite popular all over the world.

If we compare this technology with ordinary window gluing, then its advantages are obvious. Since it allows you to freely ventilate the room even in winter.

To carry out the insulation procedure, you will need:

rubber seal;
silicone sealant.

To begin with, the window is removed and its sashes are dismantled. Next, using a pencil and a ruler, you need to outline the place in which the niche for the sealant will be located. It is installed around the entire perimeter of the frame.

A router will be an excellent assistant for cutting a niche. After that, a seal is inserted into it. But the work does not end there, you should check the evenness of the window, the correspondence of all corners, tighten the hinges and replace, if necessary, the fittings. A silicone sealant is used to seal the joints between the glass and the window frame. If it gets on the glass surface, do not remove it immediately, but wait until it dries completely and use a razor blade to remove the congealed mixture.

Please note that Swedish seals are available in different sizes. The selection of material is carried out in accordance with the size of the gap to be sealed. The dimensions of the seal are from five to twelve millimeters.

After installing the window frame, all joints are completely sealed. In addition, it is possible to paint the window.

Advantages of window insulation using Swedish technology:

a significant reduction in heat loss, which will have a positive effect on heating costs;
environmental friendliness and harmlessness of the materials used does not cause allergic reactions;
the speed of the process, which lasts about 180 minutes;
no need for constant gluing of frames in the winter season;
no dust and dirt during operation;
after restoration, the window will serve for several more years;
the appearance of condensate masses between two glass panes of a wooden window is excluded;
the absence of drafts will improve the comfort in the room and help to avoid illness;
insulation of windows using Swedish technology allows you to increase the temperature in the room by 3-5 degrees;
the soundproofing properties of windows are improved - street noise and the sounds of cars are not heard;
the overall appearance of the window remains unchanged, the insulation is practically invisible.

Swedish technology for insulating wooden windows: general recommendations

1. Thoroughly wash the windows before starting any work.

2. Check all window accessories for correct operation. Inspect the locking mechanisms and doors.

3. Remove the sashes from the hinges, so as not to spread dirt in the apartment or in the house, it is better to take them out into the street.

4. Adjust the sashes, remove excess paint from them.

5. Start sawing the groove for the seal.

6. Install the seal, make sure it fits tightly to the window.

7. Carry out a series of insulation works on the inner and outer sides of the window sashes.

8. Reinstall the shutters.

9. Start replacing the fittings.

10. Check the system for drafts. To do this, bring a sheet of paper or a lighted match to the window.

Do-it-yourself window insulation technology, characteristics of the seal

A tubular material called EuroStrip is used as a sealant for window insulation using Swedish technology. It is based on silicone rubber made in Sweden. It is this material that has the following advantages:

resistance to temperature extremes;
resistance to exposure to chemical and paint materials;
the duration of operation is more than 15 years.

We suggest that you familiarize yourself with the main types of EuroStrip insulation used in the process of work:

1. Silicone based sealant - soft and elastic texture, good shrinkage. Resistant to alkyd or acrylic paints. Used to seal the largest gaps.

2. The rubber-based seal is hard and rough to the touch. Seals well only slots of the same width. It is unstable against paints and varnishes, it has a lower cost compared to a silicone seal.

3. The sealant in the form of thermoelatoplastic - unstable against temperature extremes, but the cheapest.

To carry out work on self-insulation of windows using Swedish technology, you will need:

large construction stapler;
milling cutter;
silicone based sealant;
staple staples;
a roller with a handle to help install the seal;
screwdrivers;
pliers;
vacuum cleaner;
stationery knife.

Clean the doors from mold, paint residues or old gaskets. Replace fittings. Replace glasses if necessary. Remove the sashes from the hinges. When carrying out work in the winter, take care of installing a protective screen to prevent heat loss in the room.

Using a router, cut a groove no more than half a centimeter deep and up to three millimeters wide. When you get close to the areas where the loops are located, leave a gap of one and a half centimeters between them and the groove.

Install the seal using a special roller, pumping it with this tool. When rolling, it is recommended to make backward movements, which will prevent strong stretching of the material and its damage.

Refit the sash and paint it if necessary. Use hot glue to seal the cracks in the wooden parts of the window.

Varieties of windows that can be insulated using Swedish technology

1. Windows of the pre-revolutionary period are distinguished by their splendor, large size, beautiful carving and high cost. The presence of such windows in the house ennobles it, but almost all types of these windows need repair. In most cases, such windows have upper sections made in the form of an arch or a stationary fragment. Their insulation implies the installation of a seal along the perimeter of the fragment, if there are glasses on the putty, they are removed and installed using silicone sealant. If the fittings in the form of beautiful forged parts are inoperable, they have to be replaced with ordinary metal locks. Of course, with a complete restoration of windows, it is possible to manufacture fittings to order, but this procedure will be very expensive. Sashes on such sashes do not have a rebate, so the seal is installed directly around the perimeter of the box. If necessary, use polyurethane foam to seal the joints between the wall and the window.

2. Insulation of windows of the Stalinist period requires caution and care. This type of windows is particularly durable and of high quality. In their manufacture, the best quality timber was used. As the locking mechanisms of such a window, a latch is used, which is distinguished by its reliable locking. They are being replaced by alternative locks.For fixing with a stack, a putty made from natural drying oil and metal-containing powders was used. It is recommended to replace these glasses with more modern ones. The seal is installed around the perimeter of the box.

3. Restoration of the windows of the double-glazed windows of the Khrushchev era implies a collapsible structure, consisting of several parts, similar to modern double-glazed windows. The seal is installed along the perimeter of the sashes, which are removed one by one from the window.

How to quickly insulate windows using Swedish technology

There is another less expensive option for window insulation, which involves gluing a silicone seal to the sash surface.

Before you get acquainted with this method, we propose to consider the advantages of silicone seals over their counterparts:

resistant to mechanical stress;
low abrasion;
good insulating qualities;
waterproofness;
resistance to exposure to ultraviolet radiation;
softness and elasticity;
duration of operation;
mold and mildew do not form on its surface;
use at temperatures from -70 to +150 is possible.

If there are no skills in working with a cutter or for some reason it is impossible to make a niche for a sealant, there is an easier way to insulate windows. There are two variations of it:

installation of the seal with a stapler;
fixing the seal on the surface of the door frame with special glue;
use of a self-adhesive sealant.

All these methods are less expensive than the previous ones and help to achieve the effect of warming only for a certain time, from one to two heating seasons.

Therefore, before choosing a method for insulating windows using Swedish technology, you should weigh all the options and think whether it is worth doing, or it is cheaper and more practical to buy a new window.