Do-it-yourself door insulation technology in the bath

The choice of insulation

Nowadays, a lot of different types of insulation are produced. However, not all of them are suitable for a bath. As a heater, you can use fur from old jackets, the outer fabric of a coat.

There are two main methods of insulating a sauna door:

1. insulation material is placed in the inner chamber of the door;
2. the insulating material is attached to the wooden door by means of dowels; to give the appearance of aesthetics, it is closed with some decorative elements.

The main criterion when choosing a heater for a bath door is flammability. Another important indicator is vapor permeability. Materials such as polyethylene and polystyrene foam cannot pass through the steam coming out of the bath, therefore they immediately create a "greenhouse" effect. As a result, a wooden door insulated with such a material quickly becomes wet and its quality decreases.

What material is better to insulate the doors of the bath

In a traditional Russian bath, a small wooden door is installed. Its maximum size is 180x70 cm. The old one dries up, cracks appear on the canvas. It is also necessary to insulate a new sealed door, the fact is that the gaps between the canvas and the frame remain in any case. A gap of 0.5 cm is necessary so that the structure does not stop functioning when it swells. If you do not insulate the entrance box, then the heat loss in the steam rooms will be 60% higher. According to statistics, 20% of the heat goes through non-insulated windows, 10% through the ceiling, 10% through the floor and the rest through a poorly insulated door.

Various materials are used to insulate the bath door: expanded polystyrene, various types of basalt material, fiberglass. But you should not use any kind of insulation in the steam room. The material must be environmentally friendly, not afraid of moisture and pass oxygen well.

There are several ways to insulate the door, the most common from above or inside the box structure. When insulating from above, the material is covered with facing, for example, linden clapboard to give an aesthetic appearance.

The main criterion for choosing a material is vapor permeability. The use of various expanded polystyrene and polyethylene materials leads to the destruction of the wooden structure. She stops breathing and the tree gets wet from wet steam. We will not talk about the combination of moisture and wood once again.

Among the most popular breathable materials are felt, basalt wool, ecowool, foil insulation.

Attention! Do not use foam rubber to insulate the door to the steam room. It absorbs moisture well and keeps it inside for a long time. The canvas will begin to rot and the structure will quickly become unusable.

Felt

Felt is either natural wool or mixed (30% synthetic fiber / 70% natural, 50% / 50%). Only natural material is suitable for the steam room. Synthetics, when sparks hit it, quickly ignite, natural wool will smolder and smoke heavily. This will be a signal to the owners.

Felt for insulating doors is taken only completely natural.

• moisture evaporates quickly without staying in the material for a long time;
• keeps warm well;
• the construction "breathes";
• easily assembled with your own hands.

The main disadvantage of the material is the high price. For comparison, 1 m of natural felt costs from 1800 rubles, fiberglass from 120 rubles.

Basalt wool

Basalt wool is a natural material that breathes and allows steam to pass through well. Consists of natural basalt fibers. Sold in rolls or mats.To insulate the entrance box in the steam room, an insulation no more than 1 cm thick is used.

Basalt wool for warming the bath door is suitable because it is not afraid of high, low temperatures.

The material has advantages:

• "Breathes";
• does not absorb moisture;
• low price;
• easy to attach to the canvas.

It was believed that basalt wool has no negative sides. But recently, scientists have found that fiber binder glue, when heated, releases toxic fumes of phenolphthalein. And judging by the reviews, when interacting with wet steam, basalt begins to smell unpleasant. Therefore, we do not recommend using basalt insulation.

Folgoizol

Folgoizol for a steam room has a lot of advantages:

• reflects steam in the steam room;
• does not allow cold air to penetrate inside;
• the material is lightweight and can be easily mounted on the door leaf;
• is an additional waterproofing;
• low price.

The downside is that it is possible to insulate a bath structure with such a material only from the inside of the steam room, since during the exterior decoration moisture will get to the wood.

When the material is selected, it is necessary to decide on the method of insulating the bath entrance structure. We will tell you about a few of the simplest ones that are easy to do with your own hands.

Creation of a frame for insulation

The most popular option for insulating a door to a bathhouse is to nail a frame made of bars 1.5–2 cm thick on the door. Between the outer border of the frame and the edge of the door leaf there should be a distance equal to 1/4 of the narthex (about 1.5 cm) plus another 1 cm The insulation is folded in half and nailed to the frame with small nails.

It will not be superfluous to place a sheet of hardboard inside the frame, but this is not necessary. As a result, when the door is closed, the insulation material rests against the door block, while it bends slightly outward, this allows completely blocking the path of cold air. With this method of insulation, the door always remains dry and cold air does not enter the bath room. In terms of time, this work takes about 1.5 hours.

How to insulate the door in the bath with your own hands

Today, manufacturers present a wide range of modern heaters for various purposes on the thermal insulation market. Depending on the raw materials and manufacturing technology, the following types of thermal insulation are distinguished in construction: basalt heaters, expanded polystyrene and extruded polystyrene foam, foamed polyethylene foam, etc. But, what is the best way to insulate the steam room door in the bath yourself?

When choosing a heater, you should pay attention to the following points. The first important characteristic is the flammability of the material. Penofol, izolon and other insulation made of foamed polyethylene foam should be used at temperatures up to + 100C, expanded polystyrene and polystyrene up to +75 degrees Celsius. Basalt heaters (Rockwool, URSA, Izorok, etc.) are made of rocks, so they are not afraid of an open flame.

Next, you should compare heaters for thermal conductivity and pay attention to vapor permeability. Expanded polystyrene and foamed polyethylene foam do not allow steam to pass through, do not absorb moisture, therefore, even in a humid environment, these materials do not lose their characteristics. Basalt thermal insulation without high-quality waterproofing is capable of absorbing moisture, while losing its thermal insulation properties.

Energoflex

The easiest and quickest way to insulate the door to the bathhouse is to use the energy flex pipe insulation. It should be positioned along the edge of the door and secured with construction tape. Everything must be done in such a way that the door can then be closed freely. Then, metal slats are attached to the fixed material so that during operation nothing leaves the door. This work will take only 10 minutes.

The result is quite effective, since the material will spring with the surface as needed, and if the door is not very flat, it will repeat its shape. If the insulation deteriorates in any way, it can be easily repaired.

How to choose the right door to the dressing room

In the room dividing the dressing room and the street, it is necessary to select the door carefully, paying attention to the details. After all, the comfort of the pastime directly depends on what quality the design will be. Of course, it is best to give preference to doors that are specially designed for. Such structures are pre-fabricated from the required material and have many advantages over standard structures.

An example of a door trim with leatherette

A lot depends on the door to the dressing rooms. Care should be taken to this issue for the following reasons:

• It is thanks to this design that temperature stability can be ensured in a space that is close to the street;
• In the room, you can create a cozy atmosphere thanks to the correctly selected materials from which the door is made;
• And also with the help of proper processing, insulation and thinking about what the structure should be, the owner of the bath can use the room for its intended purpose for a long service life.

The appearance and design of the door to the dressing room
What nuances need to be taken into account before buying a door to the dressing room in order to acquire such an element for a long time and will fully fulfill its functions:

1. The size of the doorway. This is very important, because if the structure is larger or smaller than the connector, difficulties may arise, both during installation and during operation. Therefore, before you go shopping or start the independent production of a door, you should carefully and with millimeter accuracy calculate what size it should be.

   
   Diagram of the device of the doorway and door

2. Material. Of course, it is very important to select the right raw materials for manufacturing or when choosing a finished structure. The ideal material for the door to the dressing room is wood. It is imperative to take this fact into account when purchasing elements or when buying a finished product. If you take into account plastic, which is sometimes cheaper, then you should immediately exclude this idea from the list. Plastic is a material that does not tolerate regular high air temperatures and high humidity. Also, with the constant influence of factors negative for raw materials, such a door can smolder, deform and cause other troubles. It is better to give preference, they also give a unique aroma - natural, and serve for a long time.
   

   The best option is a door made of alder, linden or aspen, this material is ideal for both quality characteristics and impact on human health.

   Preparing a wooden door for the installation of insulation

   

3. Warming. This moment is especially important. After all, only the floor, ceiling and, of course, doors are the key to organizing the right space. By correctly insulating the door structure, it is possible to maintain the stability of the air temperature in the space, the durability of the room and a harmonious atmosphere.

All the nuances are very important, so each of them should be given due attention.

Warming with a thermal curtain

There is another way to prevent cold air from entering the room - creating a thermal curtain.

To do this, perform the following sequence of actions:

1. A sealing frame is manufactured. Let's look at a specific example. Let's say the door is 80 × 180 cm.It is necessary to cut strips with dimensions of 10 × 100 cm and 10 × 200 cm from a soft seal for a bath door, two pieces each, that is, you should get 4 strips. The cut strips are nailed with small nails along the perimeter of the door frame at a distance of 2 cm from the edge.
2. Bars are sawn in dimensions 184 × 2 × 2 cm and 80 × 2 × 2 cm, 2 pieces each. Then they are installed on top of the insulation and fixed. Then they need to be wrapped with the same insulation material. All unnecessary is cut off. The edges are closed from the outside with a casing. The result is a neat rectangle.
3. A curtain with dimensions of 1.20 × 2 m is made. For this, you can use dermantin or tarpaulin. On the left, the fabric must be tucked up and hemmed in such a way that a 2 × 2 × 200 cm bar fits into this lapel. A bar is placed in the fabric and fixed.
4. About 10 cm recedes from the cashing and a bar is screwed to the wall. Then it is covered with a decorative element. Several rings (6-8 pieces) must be sewn to the upper edge of the curtain.
5. A distance equal to the diameter of the rings is laid up from the decorative strip. A self-tapping screw 60 mm long is taken and screwed in so that about 20 mm remains outside. On the other hand, similar actions are taken. A strong wire 1 m long should be attached to the self-tapping screw and pass it through the curtain rings and fasten the end to a free self-tapping screw.
6. To the left of the door, you need to attach two springs or hooks. Exactly opposite them, rings are sewn to the curtain. This makes it easy to move the screen to the side and secure it.

In the unfolded state, the screen is tightly adjacent to the sealing frame. In this case, the door from the inside will not fog up and ice.

The above methods of insulating the entrance bath door are easy to implement and allow you to reliably protect the room from the penetration of cold air from the street.